A metal powder sintered filter is a rigid porous part made by shaping metal powder and sintering it so the particles bond and leave an interconnected pore network. HuiRui lists a metal powder sintered filter product; that page describes molding by cold isostatic pressing or compression molding, then sintering at high temperature, and it lists custom sizes from a drawing or the application. The part is not a stack of woven meshes that have been sintered together, not a sintered fiber felt, and not a laboratory fritted filter simply because it is porous. This guide explains how to name the metal and the form, which dimensions belong in one enquiry, how to read a grade, bubble-point or permeability figure, and what to send for a quotation. The article does not recommend one grade over another, and it is not a fixed HuiRui catalogue.
What a metal powder sintered filter is — and is not
- A porous body formed from metal powder. Powder is shaped and then sintered. The product page names cold isostatic pressing (CIP) or compression molding, and later also lists CIP, HIP and mold pressing among the process options. Treat those as listed process routes, not as a method already chosen for every part. Confirm the route only when the drawing already requires it.
- Not multilayer sintered mesh. Sintered mesh is made by stacking, compressing and sintering layers of woven wire mesh. Those layers still have a mesh count and a weave. A powder-sintered body does not. See multilayer nickel sintered mesh: layers and mesh count. HuiRui also lists nickel sintered mesh, stainless steel sintered mesh and sintered Dutch weave mesh as mesh laminates. Do not copy a layer stack or a mesh-count call-out onto a powder-sintered enquiry.
- Not metal fiber felt. Fiber felt is a sintered sheet of metal fibers, usually specified by porosity and thickness; see nickel fiber felt porosity and thickness and stainless steel fiber felt for AEM electrolyzers. A powder-sintered filter is not a fiber sheet.
- Not unsintered woven mesh, foam, expanded metal or perforated plate. Woven cloth is named by mesh count, wire diameter and weave; foam is a cellular metal; expanded metal is slit and stretched; a perforated sheet is a punched plate. See how to specify nickel foam, felt or mesh, expanded metal mesh: LWD and SWD and perforated metal sheet: hole pattern and pitch. A woven-mesh opening or an open-area percentage written for square weave should not be used as the rating of a powder-sintered pore network; see nickel mesh open area and porosity.
- Not automatically a laboratory fritted filter. A process filter in the form of a disc, tube or cartridge is not a laboratory frit unless the enquiry says that it is. ISO 4793 grades laboratory sintered (fritted) filters by a pore size index in one of eight classes; its official public abstract limits that standard to laboratory filters made of glass, vitreous silica, ceramics, metals and plastic materials. ASTM E128 covers determination of maximum pore diameter and permeability of rigid porous filters used in the laboratory for filtration or diffusion, and is applicable to filters of sintered glass, ceramic, metal or plastic. If you need a laboratory filter designation, name the standard and the grade or method you already have. If you need an industrial or process element, do not borrow a laboratory class as a substitute for material, form, dimensions and the rating method you actually use.
- Name the metal and the grade. The product page lists metal powders such as stainless steel, bronze, nickel or titanium, and later names options that include SS304, SS316L, bronze, titanium and nickel alloys. Give the alloy designation already on the drawing or in your specification, and confirm it per enquiry. Do not assume a corrosion rating, a temperature limit or a service life from a material name alone.
Dimensions and form that belong in one enquiry
Put the items below in one enquiry. They are a way to name the filter, not a HuiRui stock list.
Material and grade. Give the metal and the grade, and any surface or cleanliness condition already required.
Form. Say whether the part is a disc, tube, cartridge, cone, plate, or another shape. Those forms are listed on the product page; a custom shape still needs a description or a drawing.
Overall dimensions and wall thickness. For a disc or plate, give diameter or width × length, and thickness, with units. For a tube or cartridge, give the outside and inside diameters or the wall thickness, the length, and which dimension is which. A single “size” label is not enough if the wall thickness is missing.
End connections, if any. The product page lists threaded, welded, flanged, tri-clamp and customized connections. If the element has an end fitting, name the type, size and standard you already use, or attach the drawing. A connection type is not implied by the porous grade alone.
Duty and how any rating was measured. State the intended duty — liquid filtration, gas filtration, diffusion, or a support role — and the fluid or gas you already know. If you already have a filtration grade, a pore-size figure, a bubble-point pressure or a permeability value, write the number with its units and name the method behind it. Those four kinds of number are not interchangeable labels.
Operating conditions you already know. Temperature, pressure or cleaning method help when you already have them. The product page lists backflushing, ultrasonic cleaning and chemical soaking as cleaning options; treat that list as options on the page, not as a guaranteed cycle life or a method already approved for every metal.
A standard or a sample already in hand. If a drawing or specification already names a test method or a laboratory grade, copy that designation exactly, with the year when it is given. Naming a standard does not replace material, form or dimensions.
The product page also lists machining, laser cutting and custom assembly as post-processing options, and a filtration-grade range of 0.2 μm to 100 μm under key advantages. Treat the range as a listing on that page, not as a stock list or as a verified rating for every material and thickness, and confirm the grade and the method per enquiry. The same page includes a table headed “Technical Specifications (Sample Data)”; do not copy a sample row as a catalogue item.
How to read a grade, a bubble point and a permeability figure
A micrometre “filtration grade” can be pasted into a purchase order in seconds, yet that label alone does not identify the part or reveal the test that produced the number.
ISO 4003 specifies a bubble-test method for the pore size of filters, porous bearings, porous electrodes and other parts with interconnected porosity. Its official public abstract treats the bubble test as a quality-control check. It is not, according to that abstract, a method for assigning filter grades, and it is not a method for measuring exact pore size or the distribution of pore sizes. If you already have a bubble-point pressure or a “maximum pore size” from a bubble test, keep it, name the method, and still give the material, form and dimensions. Do not treat that figure as a filter grade or as a complete pore-size distribution.
ISO 4022 specifies a method for determining the fluid permeability of permeable sintered metal materials in which the porosity is deliberately continuous or interconnecting, under conditions such that the permeability can be expressed as viscous and inertia permeability coefficients. The official public abstract also states that the document does not apply to very long hollow cylindrical test pieces of small diameter, in which the pressure drop of the fluid along the bore might not be negligible compared with the pressure drop through the wall. A permeability value, including an air-flow figure in a sample table, is not a micrometre grade, and it is not a substitute for wall thickness and length on a long tube.
ISO 2738 specifies methods for determining the density (dry density or fully impregnated density), oil content and open porosity of permeable sintered metal materials. The official public abstract of the current 2026 edition states that the document applies in particular to porous metal bearings and to structural parts produced by pressing and sintering metal powders. If your drawing already gives a density or an open-porosity figure, include it and name the method if you have it. Do not treat a density or porosity percentage as a filtration rating, and do not assume that every filter enquiry must include an oil-content value.
If the part is a hydraulic fluid-power filter element and you already have a first-bubble or a multi-pass rating, name that method. ISO 2942 and ISO 16889 are the usual named methods for those two tests; their official public abstracts, discussed in the sintered-mesh guide, limit what those numbers mean. A first bubble point is not a filtration rating. A multi-pass rating belongs to a tested filter element under that method, not to a powder grade by itself.
A laboratory designation from ISO 4793 or a maximum pore diameter from ASTM E128, both scoped above to laboratory filters, is not a production grade for an industrial disc, tube or cartridge unless the enquiry is for a laboratory filter.
Two parts can share a micrometre label and still differ in material, wall thickness, density, permeability or form. If you already have a grade, keep it, and still send the fields in the previous section.
Nearby forms
| Form | What it is | What to specify first |
|---|---|---|
| Metal powder sintered filter | A rigid porous body shaped from metal powder and sintered | Material and grade, form, overall dimensions and wall thickness, connections if any, and the method behind any grade or pore-size figure |
| Multilayer sintered mesh | Woven wire cloths stacked and bonded by sintering | The layer count, the mesh count of each layer, and the finished laminate thickness (43513) |
| Fiber felt | A sintered sheet of metal fibers | Porosity and thickness (43460, 43463) |
| Unsintered woven mesh | Interlaced wires | Mesh count, wire diameter, weave, opening (21806, 43519) |
A filtration-grade number is not a mesh count, and it is not a reason to leave the form or the wall thickness out of the enquiry.
HuiRui also lists a pleated sintered filter element for polymer melt product separately. If the drawing is for a pleated element, say so; that geometry is not implied by a powder-sintered disc or tube.
What to send for a quote
You do not need a full test report to write the first message. A sketch, a drawing, or an approximate size and grade is a sufficient starting point. Include the following items if you already know them:
- The job: liquid or gas filtration, a diffuser, a support, or another use, and the fluid or atmosphere if known.
- Material and grade, and any surface or cleanliness condition.
- Form: disc, tube, cartridge, cone, plate, or a drawing of another shape.
- Overall dimensions and wall thickness, with units, and the quantity.
- End connections, if the part has them, including type and size or a drawing.
- Any filtration grade, pore-size figure, bubble-point or permeability value you already use, with units and the method behind it.
- Any standard or sample you already use.
We review powder-sintered-filter enquiries against the metal powder sintered filter listing. Material, form, dimensions and the rating method are confirmed per enquiry. Related constructions include multilayer sintered mesh, nickel sintered mesh and the fiber felts described in the nickel fiber felt guide. Do not treat product-page marketing, a sample-data row, or a laboratory class as verified performance for every part. Attach the drawing and any grade or method already in use, and we will say what can be made.
HuiRui • tzx@nickelfoam.com
References
- ISO 4003:1977, Permeable sintered metal materials — Determination of bubble test pore size. https://www.iso.org/standard/9678.html
- ISO 4022:2018, Permeable sintered metal materials — Determination of fluid permeability. https://www.iso.org/standard/72838.html
- ISO 2738:2026, Sintered metal materials, excluding hardmetals — Permeable sintered metal materials — Determination of density, oil content and open porosity. https://www.iso.org/standard/85913.html
- ISO 4793:1980, Laboratory sintered (fritted) filters — Porosity grading, classification and designation. https://www.iso.org/standard/10772.html
- ASTM International, E128-99(2019), Standard Test Method for Maximum Pore Diameter and Permeability of Rigid Porous Filters for Laboratory Use. https://www.astm.org/e0128-99r19.html