Expanded metal mesh is made by slitting a metal sheet and stretching it into an open pattern, usually a diamond. It is not a woven wire cloth, not a perforated plate, and not a metal foam. The openings are described with a different set of dimensions from mesh count and wire diameter. This guide explains those dimensions, how raised and flattened finishes differ, and what to send for a quotation. It is not a ranking claim or a list of fixed HuiRui catalogue numbers.
What expanded metal mesh is — and is not
- A sheet that has been slit and stretched. The Expanded Metal Manufacturers Association (EMMA), a division of NAAMM, defines expanded metal as metal that has been slit and drawn into an open mesh pattern in a single operation. The sides of each opening are strands; the solid junction where two strands meet is a bond. HuiRui lists an expanded metal mesh product for filter-support and industrial enquiries. The product page lists stainless steel, aluminum, carbon steel and epoxy-coated expanded mesh, a diamond or standard expanded pattern, and supply as sheets or rolls. Thickness, opening size and cut size are discussed to the enquiry.
- Not woven mesh. Woven mesh is made of interlaced wires and is specified by mesh count, wire diameter and opening. A square-weave open-area formula should not be transferred to expanded metal. See nickel mesh open area and porosity and titanium woven wire mesh.
- Not perforated plate or “plate mesh”. A perforated sheet has holes punched from plate, and the punched material is removed. That construction is specified by hole diameter, pitch and pattern, not by LWD and SWD. HuiRui lists a perforated metal sheet product separately.
- Not knitted mesh, foam or fiber felt. Knitted mesh is made of interlocking loops; see nickel knitted mesh thickness. Foam and felt are three-dimensional porous structures and are specified differently; see how to specify nickel foam, felt or mesh.
- Name the metal and the grade. For stainless steel, state the grade (for example 304 or 316) if you already have it. EMMA’s recommended nomenclature likewise asks for the stainless type to be specified. If you need a metal that is not among the types listed on the expanded-mesh product page, say so explicitly rather than assuming it is the same item.
LWD, SWD and the other dimensions that belong together
EMMA 557-25, Standards for Expanded Metal, is the industry terminology used below. NAAMM’s public introduction to expanded-metal specifications also points to ASTM F1267 as a related steel specification that uses the same dimension names. Those documents describe how to name and check a pattern; they are not a HuiRui stock list.
SWD and LWD. SWD is the nominal short way of the diamond; LWD is the nominal long way of the diamond. Design size is the actual SWD and LWD, measured from a point on a bond to the corresponding point on the next diamond. When both are stated, the short dimension is conventionally given first.
SWO and LWO. These are the short and long ways of the opening — the clear aperture inside the strands, which is smaller than the bond-to-bond design size. If a drawing gives an “opening size,” say whether that number is the design size (LWD × SWD) or the clear opening (LWO × SWO).
Strand width and strand thickness. Strand width is the amount of metal fed under the dies to produce one strand. Strand thickness is the thickness of the base metal. EMMA notes that strand width and thickness can be varied to create different openings, and that the width of the strand should equal or exceed the thickness of the base metal. Those are naming and design conventions in the standard, not a guarantee for every custom part.
Overall thickness, and raised versus flattened. Standard expanded metal, also called regular or raised, leaves the press with the strands and bonds set at an angle to the plane of the sheet, so the overall thickness is greater than the base-metal thickness. Flattened expanded metal is cold-rolled after expansion to produce a smooth, flat sheet; the flattening step also reduces the original thickness of the base metal. Say which finish you need, and say whether a thickness figure is base-metal thickness, overall (raised) thickness, or thickness after flattening.
Sheet or roll size, and orientation. Give finished width × length, or a cut-part drawing, and say whether you prefer a sheet or a roll. Because the diamonds are longer in one direction than the other, state how LWD and SWD should lie in the finished piece if that matters for forming, flow or stiffness. Traditional style labels (a fraction plus a gauge number) can be a useful starting point, but NAAMM notes that some conventional labels no longer match the literal opening or gauge. Record the measured dimensions rather than relying on the style name alone.
Open area. Projected open area is still a useful description, but it must be stated for this construction and this method. Do not copy a woven-mesh calculation. See the open-area guide.
How to read published electrode studies
Expanded nickel mesh also appears in electrochemical research as an electrode or current collector. Lee and colleagues (2021) compared woven nickel meshes and expanded nickel meshes as cathodes for hydrogen evolution in a three-electrode cell with 30 wt% KOH. In their samples, the structure–performance relationships were not the same for the two constructions: the opening-to-strand-width ratio was important for the woven meshes, while structural surface area was important for the expanded meshes. Those overpotentials, and the meshes they tested, belong to that study. They are not a specification for HuiRui products, and they do not identify a single “best” LWD or SWD. Our alkaline nickel-mesh guide and open-area guide already discuss that comparison. The practical point for a purchase order is the same: name the construction, then give the expanded-metal dimensions above, and do not treat a woven mesh count as a substitute.
What to specify (and what not to copy)
Construction and finish. State that the part is expanded metal, and whether it is raised (standard) or flattened.
Pattern dimensions. Give LWD and SWD, and LWO and SWO if you have them. Include the units and which measurement each number is.
Strand and thickness. Give strand width, base-metal (strand) thickness, and overall thickness if you have them, and say which is which.
Material. Name the metal and grade, and any coating (including epoxy) or surface condition already required.
Finished size and form. Width × length or a drawing; sheet or roll; edge condition (for example a closed bond edge or an open random edge) if it matters; any further shearing or forming.
Duty. Filter-element support, protective screen, electrode or current collector, or another use. For filtration, add the medium and any support-layer notes you already have; for an electrode, add the cell or coating context. Do not treat a published cell result, or a style label, as a guaranteed rating.
Do not treat product-page marketing claims, a traditional style name, or the literature results above as verified performance or as a guaranteed production range for every order.
Expanded metal and nearby forms: a quick comparison
| Form | What it is | What to specify first |
|---|---|---|
| Expanded metal mesh | A sheet slit and stretched into an open pattern, usually a diamond | Raised or flattened; LWD and SWD (and LWO/SWO if known); strand width and thickness; overall thickness; metal and grade; cut size or roll |
| Woven wire mesh | Interlaced wires | Mesh count, wire diameter, weave, opening (21806, 43415) |
| Perforated metal | Plate with punched holes | Hole size, pitch, pattern, plate thickness, metal (perforated metal sheet) |
| Knitted mesh | Interlocking wire loops | Construction and thickness condition (43386) |
A pattern that performed well in one published cell is not a specification for every expanded sheet, and it is not a reason to omit LWD, SWD or the raised/flattened condition from the enquiry.
What to send for a quote
You do not need a complete laboratory list to contact HuiRui. A sketch, a drawing, or an approximate size and opening is enough to start. The items below help when you already have them:
- The job: filter support, screen, electrode or current collector, or another use.
- Material and grade, and any coating or surface condition.
- Raised (standard) or flattened finish.
- LWD and SWD, and LWO and SWO if you have them, with units.
- Strand width, base-metal thickness and/or overall thickness, saying which is which.
- Finished width × length, sheet or roll, quantity, and edge or orientation notes if you have them.
- A reference sample or a style label if that is how the requirement was first written, together with the measured dimensions above.
We supply expanded metal mesh in the materials listed on the product page. Thickness, opening size and cut size are confirmed per enquiry. Related constructions include perforated metal sheet and the woven meshes described in the open-area guide and the titanium woven-mesh guide. Do not treat product-page marketing claims, style labels, or the literature results above as verified performance for every design. Send the drawing and the items you already know, and we will reply with what we can make.
References
- Expanded Metal Manufacturers Association (EMMA), Division of NAAMM, Standards for Expanded Metal, EMMA 557-25. https://naamm.org/wp-content/uploads/2026/05/EMMA-557_2025-Final.pdf
- NAAMM, “Expanded Standard: What You Need to Know”. https://naamm.org/news/expanded-standard-what-you-need-to-know/
- H. I. Lee, H.-S. Cho, M. Kim, J. H. Lee, C. Lee, S. Lee, S.-K. Kim, C.-H. Kim, K. B. Yi and W.-C. Cho, “The Structural Effect of Electrode Mesh on Hydrogen Evolution Reaction Performance for Alkaline Water Electrolysis”, Frontiers in Chemistry (2021). https://doi.org/10.3389/fchem.2021.787787