Multilayer Nickel Sintered Mesh: Layers, Mesh Count and What to Specify

Multilayer nickel sintered mesh — also called nickel sintering mesh — is made by stacking, compressing and sintering layers of nickel woven mesh so that the wires bond at their contact points. It is not an unsintered woven cloth, not a knitted mesh, not a sintered fiber felt, not a powder-sintered metal filter, and not expanded metal. This guide explains those distinctions, the dimensions that belong together in a quotation, how to read a bubble-point or multi-pass figure, and what to send for an enquiry. It is not a ranking claim or a list of fixed HuiRui catalogue numbers.

What multilayer nickel sintered mesh is — and is not

  • A laminate of woven nickel mesh layers that have been sintered together. HuiRui lists a nickel sintered mesh product (the site also uses the name nickel sintering mesh). The product page describes the material as multiple layers of nickel mesh that are compressed and sintered, and it lists customization with 2 to 6 layers, a customizable mesh count, and supply in round, square, rectangular or other custom shapes. The same page lists high-purity nickel (N6) or nickel alloys such as Inconel, and a thickness range of 0.2 mm to 8 mm. Those figures are product-page listings; confirm the stack, thickness and grade for your part per enquiry.
  • Not unsintered woven mesh. A single woven cloth is specified by mesh count, wire diameter, weave and opening. Those fields still matter for each layer of a sintered laminate, but a square-weave open-area formula should not be used as the rating of the finished laminate. See nickel mesh open area and porosity and selecting nickel mesh for mechanical particle filtration.
  • Not knitted mesh, foam or expanded metal. Knitted mesh is made of interlocking loops; see nickel knitted mesh thickness. Foam is a cellular structure, and expanded metal is a slit-and-stretched sheet; see how to specify nickel foam, felt or mesh and expanded metal mesh: LWD and SWD.
  • Not nickel fiber felt. Fiber felt is a sintered sheet of nickel fibers, not a stack of woven meshes. It is usually specified by porosity and thickness; see nickel fiber felt porosity and thickness.
  • Not a metal powder sintered filter. A powder-sintered filter is molded from metal powder and then sintered. That is a different pore structure from layered wire mesh. HuiRui lists a metal powder sintered filter product separately.
  • Not the same item as unsintered Dutch weave, or automatically the same as sintered Dutch weave. Dutch weave is a weave style. HuiRui lists a sintered Dutch weave mesh product separately; that page describes a multi-layer sintered laminate that typically uses a Dutch-weave layer as the fine filtration layer, with protective and support layers. If your drawing calls for a Dutch-weave filter layer, say so, rather than assuming it is identical to a square-weave nickel sintered stack. A stainless steel sintered mesh product is also listed if the metal is stainless steel rather than nickel.
  • Not electrolytic (electrodeposited) nickel mesh. Electrodeposited mesh is made by a different route; see electrolytic nickel mesh.
  • Name the metal and the grade. If you need N6, an Inconel grade, or another alloy, write the designation you already have. Do not assume that a nickel listing and a stainless listing are interchangeable.

The dimensions that belong together

The fields below belong in the same enquiry. They describe how to name the part; they are not a HuiRui stock list.

Number of layers, and the role of each layer. State how many layers you need, and, if you know it, which layer is the filtration layer and which layers are protection or support. The product page lists customization with 2 to 6 layers. If your drawing uses a different stack, say so rather than assuming that listing is a fixed catalogue.

Mesh count and weave per layer. Give the mesh count, and the weave (for example plain or Dutch), for each layer if you have them. Wire diameter and opening for those layers are useful when you already have them. A single mesh-count label for the whole laminate is not enough if the layers differ.

Overall thickness. Give the finished thickness of the sintered laminate, with units, and say whether the figure is a free thickness or a thickness on a drawing after further forming. The product page lists 0.2 mm to 8 mm; treat that as a listing and confirm the thickness for your part per enquiry.

Material and grade. Name the metal and grade, and any surface condition already required.

Filtration intent and rating method. Say what the part has to do (for example liquid or gas filtration, a protective screen, or a support for another medium), and the fluid or atmosphere you already know. If you already have a filtration rating, name the method behind it. A bubble-point figure, a multi-pass rating and a woven-mesh opening are not interchangeable labels.

Finished size and shape. Give width × length, a diameter, or a drawing. The product page lists round, square, rectangular and other custom shapes.

Cleaning or regeneration. If you already have a cleaning method, mention it so it can be discussed. Do not treat a product-page remark about cleaning as a guaranteed cycle life.

How to read published studies or standards

A bubble-point or “maximum pore size” number is easy to copy into a purchase order, but the public abstracts of the relevant standards limit what that number means.

ISO 4003, Permeable sintered metal materials — Determination of bubble test pore size, describes a bubble test for filters and other parts with interconnected porosity. Its official public abstract states that the bubble test is a quality-control test and is not a test for defining filter grades or for determining exact pore size and pore-size distribution.

ISO 2942, Hydraulic fluid power — Filter elements — Verification of fabrication integrity and determination of the first bubble point, specifies a bubble-point method for hydraulic filter elements. Its official public abstract states that the first bubble point can be used to help locate the largest pore, and that the same test can be used to check fabrication integrity, but that the first bubble point is not a functional characteristic of a filter element and, in particular, cannot be used to estimate filtration rating, efficiency or retention capacity; it is intended for information only.

If you already have a multi-pass filtration rating for a filter element, name the method. ISO 16889 is the current ISO multi-pass method for evaluating the filtration performance of a hydraulic fluid power filter element, including contaminant capacity, particulate removal and differential pressure characteristics. That scope is the official public description of the standard. It is not a HuiRui catalogue rating, and it does not have to be run for every sintered-mesh enquiry.

Published studies of sintered multilayer mesh are likewise study-specific. Duan, Zhou and Yao (2018) prepared sintered multilayer stainless-steel wire-mesh porous plates by winding, pressing, rolling and vacuum sintering, and they measured pore size by the bubble-point method. In their mesh-only samples the pore structure was regular and most pores were smaller than 10 μm; when they enclosed metal powder between the mesh layers, the pores became irregular and the size range widened. Those constructions, pore-size figures, porosities and tensile strengths belong to that stainless-steel study. They are not a specification for HuiRui nickel sintered mesh, and they do not identify a “best” layer count or mesh count.

What to specify (and what not to copy)

Construction. State that the part is a multilayer sintered mesh (a sintered laminate of woven mesh), not unsintered cloth, not fiber felt and not a powder-sintered filter.

Layers. Give the number of layers and, if known, the mesh count and weave of each layer and which layer is intended to filter.

Thickness and size. Give overall thickness, saying what the number is, and the finished shape or drawing.

Material. Name the grade. If you need a metal other than the nickel or nickel-alloy types listed on the product page, say so explicitly.

Filtration method. If you already have a rating, name the standard or test (for example a bubble-point quality-control check, or a multi-pass element test) and the value as reported. Do not treat a bubble point as a micron rating or as an efficiency claim.

Do not treat product-page marketing claims, a service-temperature figure, or the literature and standard results above as verified performance or as a guaranteed production range for every order.

Nearby forms: a quick comparison

Form What it is What to specify first
Multilayer nickel sintered mesh Layers of woven nickel mesh compressed and sintered together Layers and mesh count (and weave) per layer; overall thickness; metal and grade; finished size or shape; filtration method if you already have one
Unsintered woven mesh Interlaced wires, not bonded as a laminate Mesh count, wire diameter, weave, opening (nickel mesh open area and porosity, nickel mesh for particle filtration)
Nickel fiber felt A sintered sheet of nickel fibers Porosity, thickness, sheet size (nickel fiber felt porosity and thickness)
Metal powder sintered filter Molded and sintered metal powder Material, finished form, and the filtration method if you already have one (product page)

A pore size or tensile result from one published laminate is not a specification for every sintered mesh, and it is not a reason to omit the layer stack or the rating method from the enquiry.

What to send for a quote

You do not need a complete laboratory list to contact HuiRui. A sketch, a drawing, or an approximate size and layer description is enough to start. The items below help when you already have them:

  1. The job: liquid or gas filtration, a protective screen, a support layer, or another use, plus the fluid or atmosphere if you know it.
  2. Material and grade, and any surface condition.
  3. Number of layers, and the mesh count and weave of each layer if you have them.
  4. Overall thickness, with units, and what the number is.
  5. Finished size or shape, or a drawing, and quantity.
  6. Any filtration rating you already use, with the method named, or a reference sample.
  7. Any cleaning or regeneration method already required.

We supply nickel sintered mesh as listed on the product page. Layer count, mesh count, thickness, shape and size are confirmed per enquiry. Related constructions include sintered Dutch weave mesh, metal powder sintered filter and stainless steel sintered mesh. The structure overview of foam, felt or mesh and the open-area guide remain useful when you are still choosing a form. Do not treat product-page marketing claims, or the literature and standard results above, as verified performance for every design. Send the drawing and the items you already know, and we will reply with what we can make.

References

Contact us Form

Leave us a message — we’ll reply within 30 minutes!
Please feel free to leave your message here, or send an email to tzx@nickelfoam.com

"*" indicates required fields

This field is for validation purposes and should be left unchanged.
Start typing to see products you are looking for.

Contact us

Leave us a message — we’ll reply within 30 minutes!
Please feel free to leave your message here, or send an email to tzx@nickelfoam.com

"*" indicates required fields

This field is for validation purposes and should be left unchanged.

*We respect your confidentiality and all information are protected.

Contact us

Leave us a message — we’ll reply within 30 minutes!
Please feel free to leave your message here, or send an email to tzx@nickelfoam.com

"*" indicates required fields

This field is for validation purposes and should be left unchanged.

*We respect your confidentiality and all information are protected.