Perforated Metal Sheet: Hole Pattern, Pitch and What to Specify

A perforated metal sheet — also called perforated plate or punched sheet — is a metal plate in which holes have been punched, leaving a pattern of openings and the metal that remains between them. HuiRui lists a perforated metal sheet product; the listing names the process as punching and the size as customized to the enquiry. The sheet is not a woven wire cloth, not a slit-and-stretched expanded mesh, and not a laboratory test sieve simply because it has holes. This guide explains how to name hole shape and size, pitch, pattern and plate thickness, how to read an open-area figure, and what to send for a quotation. It does not rank products, and it is not a fixed HuiRui catalogue.

What perforated metal sheet is — and is not

  • A punched plate. Holes are cut from a metal plate by punching. The HuiRui product page lists raw materials that include galvanized steel, stainless steel, aluminum, high-manganese steel, copper, nickel and alloy plates. The same page lists conventional hole types and custom hole types, and three hole arrangements: a straight row, a 45° staggered arrangement, and a 60° staggered arrangement. Those materials, hole types and arrangements are product-page listings; confirm the metal, grade, hole geometry and dimensions for the quoted piece.
  • Not expanded metal, and not automatically the same item as a “plate mesh.” Expanded metal is made by slitting a sheet and stretching it into an open pattern, usually a diamond. The openings are named with LWD, SWD, strand width and thickness, not with a punched-hole diameter and pitch. See expanded metal mesh: LWD and SWD. HuiRui also lists an expanded metal mesh product for that construction. In this industry the name “plate mesh” is often used for expanded metal. One HuiRui plate-mesh listing, nickel steel plate mesh, even describes expanded-metal lath types. Do not treat a plate-mesh product name, or an LWD × SWD call-out, as a perforated-sheet specification.
  • Not woven wire cloth. Woven cloth is produced from interlaced wires. Name it by mesh count, wire diameter and the weave type. Dutch weave is a woven filter cloth with unequal counts and two wire diameters; see Dutch weave mesh: warp and weft. A square-opening open-area formula written for woven mesh should not be copied onto a punched plate; see nickel mesh open area and porosity.
  • Not automatically a test sieve. A punched industrial or decorative sheet is not a test sieve unless the enquiry says that it is. ISO 3310-2 specifies technical requirements and test methods for test sieves of perforated metal plate; its official public abstract limits that standard to test sieves with round holes from 125 mm down to 1 mm, or square holes from 125 mm down to 4 mm, in accordance with ISO 565. ASTM E323 covers perforated-plate sieves with round or square apertures, normally mounted in a frame, for precision testing in the classification of materials by designated nominal particle size. If you need a test sieve, name the standard and the sieve designation you already have. If you need an industrial or decorative plate, do not borrow a sieve designation as a substitute for hole size, pitch and pattern.
  • Name the metal and the grade. Write the designation you already use. The perforated product page lists the material families above; later on the same page, stainless types 201, 304 and 316 also appear among the listings. Confirm the grade per enquiry. Do not assume a corrosion or service-life rating from a material name alone.

The dimensions that belong together

The quantities below belong in one enquiry. They are a way to name the sheet, not a HuiRui stock list.

Hole shape. Say whether the holes are round, square, slotted, hexagonal or another shape already on the drawing. The product page offers conventional or custom hole types; a custom shape still needs a clear description or a drawing.

Hole size (aperture). Give the hole size with units. For a round hole this is usually the diameter; for a square hole, the side length; for a slot, both the width and the length, and say which is which. A single “mesh” label is not a hole size.

Arrangement (pattern). Name the layout of the holes. The product page lists a straight row, a 45° staggered arrangement and a 60° staggered arrangement. Do not treat those three layouts as interchangeable. If the drawing uses another pattern, describe it or attach the drawing.

Pitch. Pitch is the center-to-center spacing of the holes. If the spacing is different in the two directions parallel to the plate edges, give both pitches and say which direction each belongs to. Hole size without pitch, or pitch without hole size, is not a complete pattern.

Orientation to the plate edges. ISO 7806, which gives a code for designating perforations in industrial plate screens, states that a perforation is designated by the shape of the holes, the aperture size, the mutual arrangement of the holes, the pitch, and the orientation of that arrangement relative to the edges of the plate. The official public abstract also states that the standard applies to perforated plates regardless of the plate material. If the pattern must run a particular way relative to the length, width or a formed edge, say so.

Plate thickness, and finished size. Give the plate thickness with units, and the finished width and length, or a drawing for a cut or formed part, plus the quantity. Size on the product page is customized according to the enquiry.

Margins and edge condition. If the drawing needs an unperforated margin, a particular starting row, or a stated edge condition after shearing or forming, include that note. Those details are not implied by hole size and pitch alone.

Surface condition. The product page lists surface treatments that include oxidation, painting, hot-dip plating, electroplating, polishing, dipping and spraying. Treat that list as a set of options on the product page, not as a finish already applied to every sheet, and name the finish you actually need.

Any standard already cited. If the drawing already uses the ISO 7806 designation system, a nominal opening from ISO 2194, the dimensional standard DIN 24041, or a test-sieve standard, write the designation as it appears, including the year if you have it. Those documents do not replace the dimensions above.

How to read open area, pitch and hole size

An open-area percentage is easy to copy into a purchase order, but it does not, by itself, identify the holes.

Projected open area is the fraction of the sheet area occupied by holes when the plate is viewed face-on. That fraction depends on hole size, pitch and the arrangement together. The same hole size at a wider pitch leaves more metal between the holes and a lower open area. Two patterns can also share an open-area percentage and still have different hole sizes, different pitches or a different layout. If you already have an open-area figure, keep it, and still give hole shape, hole size, pitch and pattern.

The remaining metal between neighbouring holes — sometimes called the bar or the ligament — is likewise fixed only when hole size, pitch and arrangement are stated together. If the drawing already gives a bar width, include it and say in which direction it is measured.

Do not calculate a punched-plate open area with the square-woven-mesh method in the open-area guide. That method uses a clear aperture and a wire diameter. A perforated sheet has no woven wire diameter. Do not use LWD and SWD from expanded metal either.

ISO 2194 gives designation and nominal sizes of openings for industrial screens of woven wire cloth, perforated plate and electroformed sheet. Its official public abstract points to principal and supplementary millimetre and micrometre series. If your enquiry already uses one of those nominal sizes, write the size as designated. The standard does not require every decorative or custom sheet to use that series.

ISO 10630 specifies technical requirements and test methods for perforated metal plate used for industrial screening and supplied in flat or coiled form. The official public abstract limits that document to low-carbon-steel plates, with nominal hole sizes from 1 mm for round holes and 4 mm for square holes up to 125 mm according to ISO 2194, and with a maximum plate thickness of 12,5 mm. It does not describe every stainless, aluminum, copper or nickel sheet, and it does not set a catalogue of hole sizes for decorative work.

A hole-size range written for test sieves is not a production range for industrial plate. ISO 3310-2 and ASTM E323, as scoped above, apply to test sieves. Do not treat their aperture lists as HuiRui stock sizes.

What to specify (and what not to copy)

Construction. State that the item is a perforated (punched) metal sheet or plate, not expanded metal, not woven mesh and not a test sieve unless that is what you need.

Pattern. Give hole shape, hole size, arrangement and pitch, with units, and the orientation to the plate edges if it matters.

Plate and piece. Give plate thickness, finished size or a drawing, quantity, and any unperforated margin or edge note.

Material and finish. Name the metal and grade, and any surface condition already required.

Standard, if you already use one. Write the designation and year. Do not treat a test-sieve standard as the specification for a general industrial sheet.

Do not copy unverified marketing from a product page, typographical grade names, or a listed application as a performance claim. Do not treat an open-area percentage, or a sieve designation, as a substitute for hole size, pitch and pattern.

Nearby forms: a quick comparison

Form What it is What to specify first
Perforated metal sheet A plate with punched holes Hole shape and size, pitch, pattern, thickness, material, sheet size or drawing
Expanded metal A slit-and-stretched sheet LWD, SWD, strand and thickness (43510)
Woven wire mesh Interlaced wires Mesh count, wire diameter, weave, opening (21806, 43519)
Multilayer sintered mesh A sintered stack of woven meshes Layers and mesh count per layer; overall thickness (43513)

An open-area percentage is not a hole size, and it is not a reason to leave pitch or pattern out of the enquiry.

What to send for a quote

A complete laboratory file is not required for the first message. A sketch, a drawing, or an approximate hole size and sheet size is a sufficient starting point. Include the following items if you already know them:

  1. The job: screening, guarding, a decorative or ventilation panel, a filter support, or another use.
  2. Material and grade, and any surface condition.
  3. Hole shape, or a drawing of a custom hole.
  4. Hole size and pitch, with units, and the arrangement (straight, 45° staggered, 60° staggered, or another named layout).
  5. How the pattern should sit relative to the plate edges, if that matters.
  6. Plate thickness, finished width and length or a drawing, any unperforated margin, and the quantity.
  7. Any standard or sample you already use.

We review perforated-sheet enquiries against the perforated metal sheet listing. Material, hole shape and size, pitch, pattern, thickness and cut size are confirmed per enquiry. Related constructions include expanded metal mesh and the woven meshes described in the Dutch weave guide and the open-area guide. A multilayer sintered mesh is a different, bonded construction. Do not treat product-page marketing, an open-area percentage, or a test-sieve range as verified performance for every sheet. Send the drawing and the hole pattern you already have; we will reply with what can be produced.

HuiRui • tzx@nickelfoam.com

References

Contact us Form

Leave us a message — we’ll reply within 30 minutes!
Please feel free to leave your message here, or send an email to tzx@nickelfoam.com

"*" indicates required fields

This field is for validation purposes and should be left unchanged.
Start typing to see products you are looking for.

Contact us

Leave us a message — we’ll reply within 30 minutes!
Please feel free to leave your message here, or send an email to tzx@nickelfoam.com

"*" indicates required fields

This field is for validation purposes and should be left unchanged.

*We respect your confidentiality and all information are protected.

Contact us

Leave us a message — we’ll reply within 30 minutes!
Please feel free to leave your message here, or send an email to tzx@nickelfoam.com

"*" indicates required fields

This field is for validation purposes and should be left unchanged.

*We respect your confidentiality and all information are protected.